Essentially, I was interested in three things to be activated with DDT4ALL – a “polite turn signal”, turning on my motor temperature and change the lower limit of the RPM of the oil pressure sensor. HSA it was the last necessity because I have a manual transmission and my wife using the car, turning on the gauges backlight when starting the engine can be forgotten because in the evening you can forget to turn on the dipped beam, and so the dark gauges will “remind” you. Below you’ll find also other good modifications.
- Gauging calibration of the fuel indicator
- Turn on the “polite turn signal”
- Rear wiper linked in with reversing
- Oil pressure sensor low limit
- Gear shift indicator
- Clock & OUT Temperature
- Backlight always ON
- HSA (HILL ASSISTANCE)
So we will start with the Preliminary operations from :
Once we are connected in DDT4ALL , we will start with the:
1. TEMPERATURE OF THE MOTOR (BARS INDICATIONS)
TDB> CLUSTER v5.0>General Configuration > Configuration Vidange
Below Screens \ GENERAL CONFIGURATION \ Configuration 2
ENGTEMP is present to be selected in ECRITURE column
Click on the WriteEngTemp, click on the button READ ALL, click on the button ACKNOWLEDGE and click on WRITE ALL for the soft reset tidy.
LEVEL BARS mean:
0 bars: below 25 ° C
1 bar: 25 – 49.9 ° C
2 bars: 50 – 74.9 ° C
3 bars: 75 – 92.9 ° C
4 bars: 93 – 102.9 ° C
5 bars: from 103 ° C
2. Gauging calibration of the fuel indicator
go to TDB> Cluster v4.9> [TDB] CMFB Cluster v4.9 > GAUGING> Calibration Affichage> where we find the original values:
Results on Dashboard Default REFILL values on DACIA SANDERO /LOGAN
Now, we can modify with new values to check and press the yellow buttons. First 2 buttons to save and insert the values and then the Prise en compte des configurations to restart the gauges.
If we see that the level has changed, that means everything is correct.
Now, it’s time for inserting our desired level values. I propose to choose the division of 6 liters; but you can choose any values. Save it again and the whole procedure is over.
Thank you all for your attention!
3. Turn on the “polite turn signal” &
4. Rear wiper linked in with reversing
UCH> GB BCM T4> [UCH] GB BCM T4 > Change configuration → Select with at 3x flashes when tapping > The value of READ column is changed to “with” .
Click on the Einstein icon at the top, including the “expert mode” and click on yelllow button” 3x flashes when tapping ” opposite the changed value.
Enjoy the functionality:
For rear wiper linked is the same story as bellow ↑
5. The lower limit of the response speed of the oil pressure sensor is 500rpm instead of 2000rpm:
TDB> CLUSTER v4.9>General Configuration > Configuration Vidange
Below Screens \ GENERAL CONFIGURATION \ Configuration Entretien et Odometrie opposite
Oil_Pressure_Threshold in the ECRITURE column we change to “500″
Click on the button, click on the button, click on the button and click on click values, then on the “Prise en compte des configurations” for the soft reset tidy.
6. Gear shift indicator & 7. Clock & OUT Temperature & 8. Backlight always ON
TDB> TDB [GB CLUSTER]>Instrument cluster > Change configuration → Select “with” at the functionalities that you want to activate.
The value of READ column is changed to “with” or “without” when you don’t want .
Click on the Einstein icon at the top, including the “expert mode” and click on yellow buttons + “SAVE” for the final implementation.
9. HSA (HILL ASSISTANCE)
ABS-VDC – ABS-ESP> ABS ESC V3.7>[ABS-VDC – ABS-ESP] ABS ESC v3.7> 1 – Configuration> 12-ECU Configuration 1> HSA Function Activation> Select “Activated by diag” at the functionalitie and then push the yellow button write HSA config. If the right information is with green: Activated by diag push “Soft reset” and that’s it.
If you know some other hidden features, please share with us 🙂